CART: Cart is empty | Checkout
Bestsellers
-
$1.25
Orange Heavy Duty Fuel Line 1/4" ID
-
$1.25
Clear Fuel Line 1/4" ID
-
$1.25
Colored Fuel Line 1/4" ID
-
$1.30
OTK Kart Numbers
-
$2.40
Freeline Birel Fuel Line
CKS
Products
- per page
Throttle Cable - Barrel End
Barrel shaped end for slide type carburetors (Animal, C-50, Shifter, Also fits in OEM KT100 Throttle Swivel)
$3.50
Two Lip Rubber Cup Brake Seal
Seals fit a variety of Master Cylinder and Calipers
Sold Individually
Sold Individually
$8.50
UI425 Grey Foam Element, 4" Long
Foam filter fits over fabric air filter, helps keep out dirt and mud
$8.95
Vinyl White Stick On Number Panel
Side, Rear Background Panel - 7 1/4" Tall, 8 7/8" Wide
Buy a 10 Pack and Save $$
Buy a 10 Pack and Save $$
$0.95
1 1/4" Lightweight Rear Wheel Hub, US Pattern, Black
Aluminum, Select 1/4" or 5/16" Hub Bolt Size
Hub is available as a 1/4" Tapped Wheel Bolt Hole or 5/16" Tapped Wheel Bolt Hole
1 13/16" Long
Hub is available as a 1/4" Tapped Wheel Bolt Hole or 5/16" Tapped Wheel Bolt Hole
1 13/16" Long
$19.50
Comet 40mm US Pattern Wheel Hub, Lightweight, Low Grip, Lipless
Short wheel hub helps free up kart, for use with one piece wheels
Includes 5/16-24 Bolts and Flange Nut, American Bolt Pattern
Includes 5/16-24 Bolts and Flange Nut, American Bolt Pattern
$45.00
Kart Master 40mm Wheel Hub Aluminum Axle Spacer Kit
Fits Most 40mm Hubs, Keeps the Wheel Hub From Sliding In Even if the Hub Loosens Up, Great for DD2
$45.00
M6 x 1.0mm Set Screw for Bearing, Course Thread
Set Screw Fits some 25mm and 30mm Axle Bearings
Not as popular for bearings as the M6 x .75 mm Set Screw (Fine Thread)
Not as popular for bearings as the M6 x .75 mm Set Screw (Fine Thread)
$0.95
Two Cycle Engine Dial Indicator, Screws into Spark Plug Hole for Ignition and Port Timing
Dial Indicator Gauge for Two Cycle Engine Port Timing and Ignition Timing
Measures in .001" increments, 2" travel range
14mm Plug Hole Size
Measures in .001" increments, 2" travel range
14mm Plug Hole Size
$113.50
Tygon Yellow Fuel and Pulse Line 3/16" ID
Sold by the Foot
3/16" ID x 5/16" OD x 1/16" Wall
Tygon Yellow Fuel Line and Pulse Line, Great for IAME Swift Pulse Line
3/16" ID x 5/16" OD x 1/16" Wall
Tygon Yellow Fuel Line and Pulse Line, Great for IAME Swift Pulse Line
$2.75
1 1/4" Adjustable Cross Cassette
Black Anodized Cross Adjuster or Lead Adjuster for 1 1/4" Bearings
$60.00
1 1/4" Extended Black Rear Wheel Hub, US Pattern
Aluminum, Black Anodized
Includes 1/4-28 Wheel Hardware, can be exchanged for 5/16" bolt kit
2 1/2" Overall Length
Includes 1/4-28 Wheel Hardware, can be exchanged for 5/16" bolt kit
2 1/2" Overall Length
$19.00
17 Red Plastic Header Cover Insert for KA100 Senior Exhaust Header
Fits IAME KA100 Senior Header, Goes inside the Exhaust Header
Measures 1 7/16" (36.5mm) at Narrowest point, then flares out
Measures 1 7/16" (36.5mm) at Narrowest point, then flares out
$1.00
208mm (8 3/16") Vented Rear Brake Disc, Cross Drilled, Steel
12mm Thick Disk, Fits a 6 Bolt Pattern Hub
$129.00
40mm Magnesium Brake Hub, 6 Bolt Metric Pattern
For 6 Bolt Brake Disc
High Quality, Made in Europe
High Quality, Made in Europe
$89.00
5/16" (8mm) Plastic Conical Washer
Select Color
Fits 5/16” or 8mm Conical Bolts
Great washer size for mounting kart seats
Fits 5/16” or 8mm Conical Bolts
Great washer size for mounting kart seats
$1.25
50mm Magnesium Brake Hub, 6 Bolt Metric Pattern
For 6 Bolt Brake Disc
High Quality, Made in Europe
High Quality, Made in Europe
$86.00
6mm Flat Head Metric Allen Bolts
6mm (1mm Pitch) Flat Head Metric Allen Bolts
Most Bolts are Silver Zinc Finish, A Few Sizes are Black Oxide Finish
Most Bolts are Silver Zinc Finish, A Few Sizes are Black Oxide Finish
$0.60
6mm Metric Three Way Compression Fitting with 2 Caps
M6 Caps and Ferrules, For Two Lines and 1 Tapered Caliper or Master Cylinder Tapped Hole
$13.95
A3. 0237.BAASS OTK Aftermarket Stainless Steel Bottom Seat Mounting Support 42mm
0237.BAASS OTK Aftermarket Stainless Steel Bottom Seat Mounting Support 42mm
Replaces 0237.BAA OTK TONY KART BOTTOM SEAT MOUNTING SUPPORT 42MM
Made from 4.5mm Thick Stainless Steel, Stronger than the Stock Steal Brackets, Longer Lasting
Replaces 0237.BAA OTK TONY KART BOTTOM SEAT MOUNTING SUPPORT 42MM
Made from 4.5mm Thick Stainless Steel, Stronger than the Stock Steal Brackets, Longer Lasting
$23.00
Aluminum Pedal Foot Grips for Larger Pedals, Metric Pedals
.575 Grip ID, 3 1/8" (80mm) Long, Sold as a Pair
$14.00
Beadmaster Tire Beading Tool
Steel Band, Adjustable tire ring for all kart tires from 450x5 up to 810x6 tires, 9 1/2" Wide
$95.00
Brass Popoff Gauge Replacement Fitting End
Replacement End for Carburetor Popoff Gauge with O-Ring
$9.50
Briggs LO206 Carburetor Slide Setting No-Go Gauges
LO206 Tech Tool for Green and Yellow Slides
To get maximum legal performance you need to make sure the slide opens to the maximum.
These Go-No-Go gauges are .005" smaller than the maximum on one end and right on the maximum on the other end. Just a few thousandths makes a big difference.
To get maximum legal performance you need to make sure the slide opens to the maximum.
These Go-No-Go gauges are .005" smaller than the maximum on one end and right on the maximum on the other end. Just a few thousandths makes a big difference.
$24.95
- per page